1

The paper size should be distinguished using the CropBox value (trimming size) in order to direct-print a PDF file. In general use, the MediaBox (media size) value is used as the standard.

The paper size is distinguished using the CropBox value (trimming size) of a PDF file.

2

When multiple print jobs are collected to a single file and printed using the LPR command, an error occurs, causing an output failure.

After receiving all data (file), execute print jobs regardless of the controller's spool setting. In this case, the printing speed may slow down.

The maximum file size that can be received for each file is within 2 GB. If the maximum file size exceeds 2 GB, no effect of setting change will be ensured.

After the setting is changed, turn Sub power switch off, and on again to confirm the setting.

4

When multiple PostScript data items are collectively output to a single file via the network, multiple data items are collectively output to a single job.

When [Ctrl] + [D] is detected, it is judged to be a job delimiter, enabling you to output them as multiple jobs.

5

When multiple PostScript data items are collectively output to a single file via USB, a single job is divided and output. Also, error pages may be output.

When [Ctrl] + [D] is detected, a single job can be output as a single job without being judged to be a job delimiter.

7

When multiple jobs are collectively output to a single file, whether or not to delimit them should be selectable by judging the range from the PJL JOBNAME command to the PJL EOJ NAME command to be a job delimiter.

Setting value

[Off]: Outputs multiple jobs as a single file without delimiting them.

[On]: Outputs multiple jobs as they are by delimiting them.

11

The paper tray of this system should always be specified automatically.

The paper tray is always specified automatically regardless of the paper tray specified in the printer driver.

12

The file name specified in the LPR command, not the job name specified in the printer driver, should be displayed as the job name.

The file name specified in the LPR command is displayed as the job name.

13

When an attempt is made to install fonts using Font Management Utility, a timeout error occurs.

A timeout error is avoided. However, the RAM font type is displayed as [HDD] in the font list of Font Management Utility.

15

In Mac OS X or later, when multiple body copies are specified with cover insertion, only 1 copy of the body is output.

The specified number of copies of the body are output.

However, if a job including font data or EPS data is output, error pages may be output.

16

When the LPR command (-J) is used in Mac OS, a banner page should be printed out.

A banner page is printed out.

However, even if the LPR port is used from the printer driver when printing, a banner page is printed out.

18

The paper type specified in [MediaType] of a PS command should be registered as the paper name.

If the specified paper name is not registered on the [Register/Delete Paper Setting] screen after it is sent to the engine, it is registered automatically.

Setting value

[Off]: Not registered.

[On]: Registered.

* To confirm the [Register/Delete Paper Setting] screen, selectUtility/Counter - [User Setting] - [System Setting] - [Paper Tray Setting] - [Paper Setting] - [Paper Profile Setting].

25

When a job with the mixed original specified, which includes an original of 8.5 e 11 v size, is output by direct printing, it is recognized as the 9 e 11 v size.

Such a job is printed with 8.5 e 11 v size.

26

PostScript error, [Limitcheck], occurs.

Reduce the occurrence of PostScript error, [Limitcheck].

* When an attempt is made to print a large number of jobs or a large capacity job, [Limitcheck] may occur.

After the setting is changed, turn Sub power switch off, and on again to confirm the setting.

27

When specific PS data is output, an error occurs, so PostScript (Level1) commands should be supported.

Setting value

[Off]: Does not support PostScript (Level1) commands.

[On]: Support PostScript (Level1) commands.

Selecting [On] allows you to use the following Level1 commands.

lettertray, legaltray, ledgertray, a3tray, a4tray, b5tray, 11x17tray

After the setting is changed, turn Sub power switch off, and on again to confirm the setting.

28

Cannot edit the job stored in the HDD using the PPD Driver in AccurioPro Print Manager.

Allows editing. However, the printing speed may slow down.

Editing is also possible even if the job is set to Save (or Save & Print) with No. 48/49.

31

When using PDF direct printing, content related to transparency may not be output.

You may be able to resolve this issue depending on whether or not device colors are used.

Setting value

[Off]: Does not use device colors.

[On]: Uses device colors.

32

When a PDF file is converted to a PostScript one, complicated transparent objects cannot be correctly converted in certain cases.

Switch the conversion method to address this problem.

Setting value

[Off]: Converts for each object.

[On]: Converts the entire page.

33

When an attempt is made to output PCL data in duplex mode, blank pages on back sides are discarded.

Also prints back sides that are blank pages. However, there is no charge for blank pages.

34

When an attempt is made to download a large number of PS fonts, it may take a long time to print the PS font list.

Only display the font name without outputting sample characters of the downloaded fonts to the font list; the PS font list printing speed will increase.

36

When an attempt is made to output PCL XL/TIFF data of the mixed-size original (A4 v/w), the bind position of a landscape original is changed compared with the original output from the PS driver.

The original is printed at the same bind position as when it is output from the PS driver.

38

When an original is printed via Linux, it is output in banner format, so banner output should be disabled.

Disable the -C option (banner creation) of the LPR command.

Setting value

[Off]: Enables the -C option.

[On]: Disables the -C option.

40

The file stored in a hot folder of AccurioPro Hot Folder should be printed on paper of a size that is closest to the size of the original in the paper tray.

When the output paper size is [Auto]; the output tray is [Auto]; and this setting is [On], the file is printed on paper of a size that is closest to the size of the original in the paper tray. However, if there is no output paper, the file is printed on paper of a size selected with a regular APS (automatic paper).

43

If MIB (kmNetHttpdEnable) is changed from "disable" to "enable", [Web Connection Setting] in [Administrator Setting] - [Controller] - [Simple Security Setting] should also be changed synchronously.

Setting value

[Off]: Does not synchronize MIB with Web Connection.

[On]: Synchronizes MIB with Web Connection.

45/46

When an attempt is made to print a job without using the printer driver or AccurioPro Hot Folder, it should be possible to specify the color mode.

The color mode can be specified.

Setting value

45/46 = [Off] / [Off]: Auto Color

45/46 = [Off] / [On]: Full Color

45/46 = [On] / [Off]: Grayscale

45/46 = [On] / [On]: Auto Color

47

When a specific PDF original (with overprint attribute) is held or printed, it may take a long time, or no data may be output.

This problem may be resolved by canceling the overprint setting that converts data from PDF to PS.

Setting value

[Off]: Uses the overprint setting.

[On]: Does not use the overprint setting.

General precaution

When the overprint setting is not used, the output result may be different.

48/49

Print, Store, or Print/Store should be forcibly applied regardless of the specification of the printer driver.

Forcibly apply the following settings.

Setting value

48/49 = [Off] / [Off]: OFF

48/49 = [Off] / [On]: Print

48/49 = [On] / [Off]: Store

48/49 = [On] / [On]: Print & Store

51

When a job involving paper that is larger than the maximum paper size supported by this system is output using AccurioPro Hot Folder, it is output as an error page without being printed, however, the center part should be printed out at the full size.

[Off]: Outputs an error page (for PS or PDF).

Reduced for output (for TIFF).

[On]: Outputs the center part at the full size.

This setting is available for PS, PDF, and TIFF.

This setting is only available when poster printing (Divided) is set to Off.

Restrictions

For PS and PDF

When [Off] is selected, if the original size exceeds the maximum paper size supported by this system, an error page is output.

When [On] is selected, if the original size exceeds 1,600 mm e 2,100 mm / 62.99" e 82.68", an error page is output.

For TIFF

When [On] is selected, if the size exceeds 900 mm e 1,320 mm / 35.43" e 51.97", images may be printed out of alignment.

55

When data with crop marks is printed, the crop marks of monochrome pages should be printed in black only, not in mixed CMYK colors.

Setting value

[Off]: Prints crop marks of monochrome pages in mixed CMYK colors.

[On]: Prints crop marks of monochrome pages in black only.

59

When using the RAW protocol, if the code EO"T0x04" code is received in use of the RAW protocol, EOT should be echoed back.

Setting value

[Off]: Does not echo back EOT.

[On]: Echoes back EOT.

61

Borderless printing should be available for a job created by the PCL5 command.

Borderless printing is available for a job created by the PCL5 command.

Setting value

[Off]: Does not use borderless printing.

[On]: Uses borderless printing

62/63

The status notification email indicating completion of a print job should be sent without using the PS Plug-in Driver.

Sends a notification mail to the administrator's address with the following settings.

Setting value

62/63 = [Off]/[Off]: Does not send a notification email.

62/63 = [Off]/[On]: Always sends a notification email to the administrator's address.

62/63 = [On]/[Off]: Sends a notification email to the administrator's address only when an error occurs.

66

In general use, the output of the settings configured in the printer driver or AccurioPro Hot Folder has priority over that of the settings configured in [Direct Print Setting] in [Controller].

The contents of [Direct Print Setting] should be output preferentially.

Setting value

[Off]: Gives priority to the setting of the printer driver or AccurioPro Hot Folder.

[On]: Gives priority to [Direct Print Setting]*.

* [Direct Print Setting] can also be set in [Printer Settings] of Web Connection for the Image Controller.

71

Whether to make the form of the PS Plug-in Driver transparent should be changed.

Setting value

[Off]: Makes the form transparent regardless of objects.

[On]: Does not make the form transparent regardless of objects.

Restrictions

If the custom screen is set, this option is not applied.

74/75

The method for handling an RGB value error in gray replacement should be changed.

The RGB value may not be equal for a grayscale image in a Microsoft Office application.

If an error is not allowed, gray replacement cannot be performed (a grayscale image is handled as a colored image).

To resolve this problem, set the allowable range of an error that is assumed to be R = G = B.

You can set the allowable range of R = G = B.

Setting value

74/75 = [Off] / [Off]: ^0

74/75 = [On] / [Off]: ^3

74/75 = [Off] / [On]: ^5

74/75 = [On] / [On]: ^10

77

It should be possible to store a PPML file in AccurioPro Print Manager, and change the number of copies for each page.

Setting value

[Off]: Does not allow the storage of a PPML file.

[On]: Allows the storage of a PPML file.

When set to [On] (about the stored PPML file):

Re-RIP is not performed to edit a job using AccurioPro Print Manager.

Any page operation such as exchange or copy cannot be performed to edit a page using AccurioPro Print Manager. However, blank insertion can be performed.

79

When images on the original over the standard size are shifted by the image shift function and output to standard size paper using AccurioPro Hot Folder (PDF only), processing should be performed so that no image missing occurs.

Perform image shift with RIP to prevent a print side missing from occurring.

Setting value

[Off]: Does not perform image shift with RIP.

[On]: Performs image shift with RIP.

Restrictions

Only the front side setting is valid, and the back side setting is invalid.

When the mixed original or finishing processing is selected, this function may not run.

This function is only compatible with PDF direct printing.

80

The image shift function (PDF only) of switch No. 79 should be applied to a PS job.

Perform image shift with RIP to prevent a print side missing from occurring.

Setting value

[Off]: Does not perform image shift with RIP.

[On]: Performs image shift with RIP.

Restrictions

It is necessary to set switch No.79 to [On].

Only the front side setting of AccurioPro Hot Folder is valid, and the back side setting is invalid.

When the mixed original or finishing processing is selected, this function may not run.

If image shift is set in PS Plug-in Driver, this function becomes invalid. When using PS Plug-in Driver, set this function to [Off].

82

When [Maintenance] tab - [Status Notification Setting] - "Replenish Paper Tray" is selected in Web Connection for the Image Controller, an email notification is issued when a regular tray is out of paper; however, it should be issued before the paper supply runs out.

Change a notification of "Replenish Paper Tray" in [Status Notification Setting].

Setting value

[Off]: Issues a notification when the tray is out of paper.

[On]: Issues a notification before the tray runs out of paper.

84

The [LPQ -P] commands used on Linux should be supported.

Setting

[Off]: No response returns when the [LPQ -P] command is input.

[On]: When the [LPQ -P] command is input, [Ready] or [Not Ready] returns depending on the device status.

When [Ready] or [Not Ready] is returned, the specifications are as follows.

[Ready]: A job can be executed.

[Not Ready]: A job cannot be recovered automatically (an error occurs, etc.)

89

The contents of setting information prints should be all printed in black characters.

Setting value

[Off]: Does not print all in black characters.

[On]: Prints all in black characters.

91

When Pure Black or Gray Replacement is used for a gradation object using APPE, the colors around the target color are also affected.

Therefore, it should be possible to select whether to apply Pure Black or Gray Replacement for a gradation object or make adjustments so that the colors around the target color are not affected.

[Off]: Also applies Pure Black or Gray Replacement to a gradation object.

However, the colors around the target color are also affected in addition to the colors targeted for Pure Black or Gray Replacement.

[On]: Does not apply Pure Black or Gray Replacement to a gradation object.

In this case, the colors around the target color are not affected.

93

When a special color included in print data is not registered in the controller, the data should be temporarily saved on the HDD without being printed, and placed in standby state as an error.

Temporarily save print data on the HDD, and place it in a standby state as an error.

Setting value

[Off]: Does not temporarily save print data on the HDD.

[On]: Temporarily saves print data on the HDD.

Restrictions

This is only applied when a regular printing or spool printing is specified.

The PS Plug-in Driver is the only available printer driver.

AccurioPro Hot Folder is the only an available application. However, note that APPE cannot be used when a PDF file is output. CPSI is only available.

If [On] is selected to make prints with a banner, banner pages are not printed.

94

When PPML data is printed on a mixed page, if a reuse object is used, a missing page will be created.

Even if a reuse object is used, creation of a missing page should be avoided by adjusting the rotation position.

Setting value

[Off]: Disables reuse object position adjustment.

[On]: Enables reuse object position adjustment.

95

The automatic paper tray selection function should be used by converting [MediaPosition1(tray2)] and [MediaPosition2(tray3)] of the PS command for paper tray specification to [MediaColor(Other)] and [MediaColor(White)].

Setting value

[Off]: Does not perform command conversion.

[On]:

[MediaPosition1] is converted to [MediaColor(Other)], and [MediaPosition2] to [MediaColor(White)].

The specifications of the [MediaColor] command are as follows.

[MediaColor(Other)]

Tray: Automatic, Paper color: Others

[MediaColor(White)]

Tray: Automatic, Paper color: White

97

Unnecessary tab paper should be discharged when a JDF-compatible application is used for printing.

Setting value

[Off]: Not be discharged.

[On]: Discharged.

98

The spine should not be made blank when [Cover Print 2 in 1] is selected for perfect binding.

Setting value
[Off]: Makes the spine blank.
[On]: Does not make the spine cover blank.

107

The Hot Folder of this system should be able to output PCL 5e files.

Setting value

[Off]: Does not support PCL 5e.

[On]: Supports PCL 5e.

If [On] is selected, the system outputs a large amount of pages on which binary data are printed when handling file formats that are not supported by Hot Folder of this system.

108

A large amount of pages on which binary data are printed should not be output when file formats that are not supported are output by a function other than Hot Folder (such as Direct Print).

Prevents printing of binary data by not supporting PCL 5e, since those formats are output based on PCL 5e. If [On] is selected, they will not be output but treated as errors.

Setting value

[Off]: Supports PCL 5e.

[On]: Does not support PCL 5e.

110

When a specific PS job* is direct-printed, the number of copies specified in PJL is not reflected, and only 1 copy is printed in certain cases. Therefore, the correct number of copies, specified in PJL, of such a job should be printed.

* The specific PS job refers to a job for which the job settings such as Staple are configured in Custom Operator of PS.

The number of copies specified in PJL has priority.

111

Staple setting should be supported in the page unit specified for a PS file.

Setting value

[Off]: Does not support the staple setting.

[On]: Supports the staple setting.

112

The print position setting (front edge, center, and rear edge) of AccurioPro Hot Folder should also be available in addition to the setting of switch No. 40.

Setting value

[Off]: Does not follow the print position setting.

[On]: Follows the print position setting.

Restrictions

It is necessary to set switch No.40 to [On].

This setting is only available for PS and PDF.

"Full Bleed" is always applied to printing.

116

When a PDF file is imported using APPE, each image should be generated based on the printing area size.

Setting value

[Off]: Based on the PDF original size.

[On]: Based on the printing area size (same as CPSI).

Restrictions

This setting is only available for the standard original.

124

The "Fit to Paper Size" function should be limited to [Reduce Only] in AccurioPro Hot Folder.

Setting value

[Off]: Reduces or enlarges to suit the paper size.

[On]: Reduces to suit the paper size (does not enlarge).

Restrictions

Some conditions are provided to use this item. For details, contact your service representative.

125

When "Fit to Paper Size" is selected in AccurioPro Hot Folder, the paper size should be switched to the printing area.

Setting value

[Off]: Suits the paper size.

[On]: Suits the printing area.

Restrictions

Some conditions are provided to use this item. For details, contact your service representative.

127

A transparent object of a Microsoft Office application should be output with high resolution. Setting at a high resolution may resolve the conspicuousness of dots that are caused depending on the transparency percentage when printing.

Setting value

[Off]: Does not set to high resolution.

[On]: Sets to high resolution.

If [On] is selected, data is always spooled for PostScript printing regardless of the machine setting.

Restrictions

This setting is only available for figures. No effect is applied to image transparency.

130

The number of copies and that of pages of a job should be printed on banner pages in PS Plug-in Driver.

Setting value

[Off]: Does not print the number of copies and that of pages of a job on banner pages.

[On]: Prints the number of copies and that of pages of a job.

Restrictions

This setting is only available for PS, PDF, and TIFF.

This setting cannot be combined with Booklet Splitting.

132

The two conflicting functions below can be set simultaneously for a PCL job.

Specify Text Margin

Horizontal Motion Index

.

By default, "Specify Text Margin" has priority in the PCL-compliant specifications, but "Horizontal Motion Index", the HP-compatible specification, should be set to be given priority.

Turn this switch [On] to change to the HP-compatible specifications.

Setting value

[Off]: Prioritizes "Specify Text Margin". (PCL-compliant specifications)

[On]: Prioritizes "Horizontal Motion Index". (specifications compatible with the HP machine)

131

In general use, banner pages in PS Plug-in Driver are output before a job, but they should be output after a job.

Setting value

[Off]: Prints in the order of banner pages -> job.

[On]: Prints in the order of job -> banner pages.

135

A notification email should be sent to the email address specified in "Status Notification Setting" under [Network Setting] - [NIC Settings] - [Detail Settings] at each of the times specified in "Print Start (Job Started)" and "Print End (Job finished)".

Setting value

[Off]: Does not send a notification email.

[On]: Sends a notification email.

Restrictions

A notification email can only be sent to "E-mail address 1".

143

All form files in the controller that can be created from PS Plug-in Driver should be allowed to be deleted all at once from tools used by the customer (the driver can only delete one at a time).

Setting value

[Off]: Does not support.

[On]: Does support.

Deleting by using the default password, "password", will delete all form data.

145

If a PPML file is printed with an application such as "Pageintegrator Pro", some characters are missing or "PPML RIPError" occurs, causing a printing failure.

The problem may be resolved by disabling the function that deletes duplicate subset fonts.

Setting value

[Off]: Enable the delete function.

[On]: Disable the delete function.

146

A font error is ignored in Adobe Acrobat, but it should be output as an error without being ignored n APPE.

Setting value

[Off]: Ignores a font error.

[On]: Does not ignore a font error.

147

When the number of sets is set to 1 or [Group] using Job Edit of AccurioPro Print Manager, the setting should be forcibly changed to [Sort].

When the number of sets is set to 1, the setting is fixed to [Group].

149

DLP (Device Link Profile) for each tab should be specified when composite printing is performed using APPE.

Setting value

[Off]: Restricts the DLP specification for each tab when composite printing is performed using APPE.

[On]: Enables the DLP specification for each tab even when composite printing is performed using APPE.

150

The color bar and color setting information should be printed on all pages when a poster is printed.

Setting value

When banner page is set for poster printing

[Off]: Prints the color bar and color setting information only on banner pages.

[On]: Prints the color bar and color setting information on all pages.

Restrictions

PDL is compatible with PS and PDF only.

This setting is only available for jobs from AccurioPro Hot Folder.

When re-RIP printing, re-RIP storage, restore, or job reset is specified from AccurioPro Print Manager, setting information is released.

Setting to [On] forcibly changes switch No. 131 to [Off].

151

The page with the Duplex command specified should be printed on the front side.

Print the page with the Duplex command specified on the front side.

Restrictions

PDL is compatible with PS and PDF (CPSI) only.

152

When direct printing is used, the setting information and color bar printing positions are different from those when PS Plug-in Driver is used.

This phenomenon occurs when the original orientation (portrait or landscape) is changed.

Portrait original: When the [Original Orientation] is set to [Landscape]:

Landscape original: When the [Original Orientation] is set to [Portrait]:

Setting value

[Off]: Sets the setting information and color bar printing positions to the same positions as when PS Plug-in Driver is used.

[On]: Matches the setting information and color bar printing positions with the original size regardless of the original orientation setting.

156

Printing stops before the last copy of multiple jobs (2 to 10 sets) sent from the VPSX server is printed.

Extending the job end detection function may resolve a phenomenon that stops printing.

Setting value

[Off]: Does not extend the job end detection function.

[On]: Extends the job end detection function.

157

The contents of Result is not output as the response result of the EOJ command, so it should be output.

Configure the setting to output the contents of Result.

Example: Result = OK, etc.

Setting value

[Off]: Not output.

[On]: Output.

158

A profile for converting CMYK data to grayscale is different between CPSI and APPE, and the CPSI profile is used ordinarily. The image quality of high-density photo data created in CMYK may be improved by using the APPE profile, so a profile equivalent to the APPE profile should be applicable.

Setting value

[Off]: Uses the CPSI conversion profile.

[On]: Uses the conversion profile equivalent to the APPE profile.

Restrictions

This setting is only available when "Use CIE Color" is set to On.

This setting is only available for PS (CPSI), PDF (CPSI), and PPML.

159

The gradation of the CMYK high-density parts is ordinarily reproduced in the APPE profile that converts CMYK data to grayscale, so areas of original data with a black density of 100% cannot be output with a black density of 100%. Therefore, such an area should be forcibly output with a black density of 100%.

An image object cannot be held with a black density of 100%, so configure the setting so that it can be held.

Setting value

[Off]: Does not maintain a black density of 100% when outputting in grayscale.

[On]: Maintains a black density of 100% when outputting in grayscale.

Restrictions

Since it is forcible output, gradation in high density areas may be damaged. It is recommended that you only use this function for the scanned text data.

If this function is set to [On], the Pure Black setting is not reflected.

This setting is only available for PS (CPSI), PDF (CPSI), PDF (APPE), TIFF (Emperor), and PPML. CPSI is only available when switch No. 158 is set to [On].

160

The maximum number of registered CMYK-CMYK direct link profiles should be extended to 100 or more.

Setting value

[Off]: Allows you to register up to 50 CMYK-CMYK direct link profiles. If 50 or more CMYK-CMYK direct link profiles are included in the database at start-up, leave only 50 profiles of which the registration date is earlier. Delete the remaining 50 profiles (however, the setting is configured so that the preset profiles and profiles specified by the color default cannot be deleted).

[On]: Allows you to register up to 100 CMYK-CMYK direct link profiles.

161

When the number of registered CMYK-CMYK direct link profiles exceeds the maximum value, it should be possible to automatically delete the oldest profile and register a new profile.

Setting value

[Off]: Disables a new registration when the number of registered CMYK-DLP direct link profiles reaches the maximum value.

[On]: Deletes the table of which the creation date and time are oldest from the list and register a new CMYK-DLP profile when the number of registered CMYK-DLP profiles reaches the maximum value.

162

When [2-Color Printing] (used as monocolor) is set in PS Plug-in Driver, if the same special color specified in the driver is included in the original at the time of printing, the density may become thin. If the same special color is included in the original, it should be printed at the same density without being changed.

Setting value

[Off]: Specifies the special color for which the plate (CMYK) is replaced for 2-color printing, and changes the special color on the original if that special color is included in the original. However, the density may become thin.

[On]: Specifies the special color for which the plate (CMYK) is replaced for 2-color printing, and outputs with the same density without changing the special color on the original if that special color is included in the original.

163

When an attempt is made to print an APPE job in AccurioPro Hot Folder, a problem in which the top-bottom order is reversed occurs, but it does not occur in a CPSI job. An improvement should be made so that such a problem does not occur in a APPE job in the same way as a CPSI job.

The following causes are assumed.

CPSI: An image is created based on the actual orientation of the original.

APPE: An image is created based on the [Original Orientation] setting of AccurioPro Hot Folder.

Setting to [On] forcibly ignores the [Original Orientation] setting of AccurioPro Hot Folder to suit the orientation of the first page of the original, and may allow you to resolve this problem.

Setting value

[Off]: Follows the [Original Orientation] setting of AccurioPro Hot Folder.

[On]: Suits the first page of the original.

* A mixed original is printed to match the orientation of the 1st page of the original regardless of the setting.

Restrictions

This setting is only available when switch No. 79 is set to [On].

164

To send scanned data using Scan To E-mail after login when [Authentication Method] of [User Authentication] is set to [External Server], the address of this email should be set to the administrator address of this system.

Changes the sender address of the email sent using Scan To E-mail.

Setting value

[Off]: Disable (The address is specified to suit the environment (for example, the authentication user's address is specified).)

[On]: Enable (The administrator address of this system is specified.)

166

If the following indirect object is included in the received PDF file, it should be detected and duplex-printed.

Indirect object:

DuplexFlipLongEdge (Print 2-Sided, Long Edge)

DuplexFlipShortEdge (Print 2-Sided, Short Edge)

Specify so that an indirect object is detected and duplex-printed.

Setting value

[Off]: Not detected.

[On]: Detected.

Restrictions

If By Page is set is enabled in each driver, it is not reflected even if [On] is selected.

This setting is reflected in PDF file version 1.4 or later. 

167

When data is printed using the PDF composite overprint function of APPE from AccurioPro Print Manager, parts that contain many objects with transparency attributes are processed, but it takes a long time.

Change the APPE rasterizing method for printing.

Setting value

[Off]: Uses the previous rasterizing method.

[On]: Uses the special rasterizing method.

Restrictions

This setting is only available for APPE.

General precaution

If [On] is selected, pages with many transparency attributes may not be printed correctly.

168

If PDF data (with transparency attributes or overprinting used frequently) using a large amount of memory is printed from AccurioPro Hot Folder when RIP is performed using APPE, output is completed at the second page in certain cases. No problem occurs in CPSI.

This problem may be resolved by switching the output method.

Setting value

[Off]: By Job

[On]: By Page

Restrictions

This setting is only available for APPE.

Important

After the setting is changed, turn Main power switch off, and on again to confirm the setting.

169

When a specific APPE job (PDF) is printed from AccurioPro Hot Folder, white or black lines appear on the printed image. No problem occurs in CPSI.

This problem may be resolved by switching the cache of the APPE display list.

Setting value

[Off]: Enable

[On]: Disable

Restrictions

This setting is only available for APPE.

Important

After the setting is changed, turn Main power switch off, and on again to confirm the setting.

General precaution

If [On] is selected, performance may decrease.

174

The "Jog" command should be supported to try page offset at arbitrary intervals.

Setting value

[Off]: Does not support the Jog command.

[On]: Supports the Jog command.

Restrictions

It is necessary to set switch No.175 to [Off].

175

Offset by Job Unit should be performed so that banner pages and the body are located at the same output position when a printer job with banner pages is sent.

Setting value

[Off]: Does not perform offset.

[On]: Performs offset.

Restrictions

It is necessary to set switch No.131 to [Off].

It is necessary to set switch No.174 to [Off].

176

A job with front and back covers should be printed immediately without being spooled.

Setting value

[Off]: Spools a job in the controller.

[On]: Does not spool a job in the controller.

General precaution

Setting to [On] does not support the back cover profile.

If [On] is selected, the following profile setting is not applied correctly.

Font/back cover printing for booklet printing

Perfect binding 2-in-1

Perfect binding 3-in-1

If [On] is selected, the following function is not applied correctly.

Booklet + Last page cover printing

177

When the user uses the following IP address, the network in user environment cannot be used.

IP address: 172.17.0.1

This phenomenon occurs because "172.17.0.1" is used as the internal address of AccurioPro Print Manager.

Setting to [On] allows you to change the internal address.

Setting value

[Off]: 172.17.0.1/16

[On]: 192.168.1.5/24

178

When a job (PS or PDF) created with the user's Knapp application is printed continuously, an error page may be inserted among pages.

The supported Readback command causes such an error, so this problem may be resolved by setting to "Other PJL Commands".

Setting value

[Off]: Support the Readback command.

@PJL ECHO

@PJL INFO

[On]: Supports other PJL commands.

@PJL USTATUS

@PJL USTATUSOFF

182

"Default Manual Settings" configured in Color Centro should be forcibly applied when a job is held.

Setting value

[Off]: Not applied forcibly.

[On]: Applied forcibly.

Restrictions

This setting is only available for CPSI and APPE. It is not available for Emperor and PPML.

183

When a PDF file including form objects is printed, part of the data is missing.

This problem may be resolved by switching the processing method.

Setting value

[Off]: Inline expansion

[On]: Form expansion

Restrictions

This setting is only available for CPSI.

184

[All] is only selectable for [Object Type] in [Tone Curve Adjustment...] of AccurioPro Print Manager.

Set to [On]; [Image] or [Text/Graphics] becomes selectable.

Setting value

[Off]: [All] is only selectable.

[On]: [All], [Image], or [Text/Graphics] is selectable.

190

Unable to send to Hot Folder in AccurioPro Print Manager (mainly from Mac OS).

This issue may be resolved by increasing the file monitoring cycle interval for Hot Folder.

Setting value

[Off]: Does not increase the file monitoring cycle interval.

[On]: Does increase the file monitoring cycle interval.

Important

After the setting is changed, turn Sub power switch off, and on again to confirm the setting.

197

You should notify the user that re-RIP is required with AccurioPro Print Manager.

Make a setting to switch the re-RIP display when printing from AccurioPro Print Manager.

Setting value

[Off]: Does not display a confirmation dialog box when performing re-RIP.

[On]: Displays a confirmation dialog box when performing re-RIP.